Exclusive Ultra Bond Technology waterproofs 95% of leaking showers without removing tilesPH 1300 519 133

Blog


The Best No Tile Removal Shower Sealing Method

By Shower Sealed | 9th November 2018

One of the most common causes of shower leaks is when the sealant – aka the ‘white stuff’ that forms a seal around the shower tray – has either been applied poorly or naturally wears down over time. When this happens, it can leave the surface exposed and greatly increase the risk of water damage.

Fortunately, it’s easy to remove the old sealant and apply a fresh new layer to form a durable watertight seal. All you need is a few handy tools and a couple of hours of your time to get the job done right.

Use these handy tools to carry out the best shower sealing method:

  • Retractable blade or knife
  • Shower sealant
  • Sealant application gun
  • Thick safety gloves
  • Roll of masking tape
  • Dry cloth
  • Mineral turpentine
  • Pointed spatula

How to Reseal Your Shower

Step 1 – Remove Old Sealant

First, you need to gently remove the old sealant and prepare the surface for the new layer.

Put on a pair of thick safely gloves to protect yourself from injury. Then use a sharp blade or knife to cut into the old sealant and scrape it off the surface. Be careful not to push the blade too far into the sealant or else you may scratch the surface.

If you find the sealant isn’t coming off easily, you may need to apply caulk remover onto the sealant to loosen it up.

Step 2 – Clean and Prepare the Surface

Once the sealant has been removed, you’ll need to clean up the bits of leftover debris and dust. Take the bottle of turpentine and pour a tiny amount onto the dry cloth. Gently glide the cloth across the remaining surface to remove these pieces – repeat until the surface clean.

To prepare the surface, use a vacuum cleaner to remove any dust or debris. Then wipe the surface with a clean dry cloth until the surface is completely dry.

Step 3- Prepare the Outer Surface

Before you apply new sealant, you want to protect the surrounding surface from a potential spill.

Stick a layer of masking tape both above and below where you’re going to apply the new sealant. Leave a gap of about 2-3mm from the wall to the joint, and vice versa for the floor to the joint – so there’s enough room for the new sealant to settle.

Step 3 – Apply New Sealant

First, take the sealant tube and equip it to the application tool. Then use a pair of scissors to cut the application nozzle at a 45-degree angle. There should be markings on the tube that indicates where you need to cut.

Now you’re ready to apply the new layer of sealant.

The best shower sealing method is to start from the inner corner of the shower tray. Gently apply pressure to the application trigger and apply a continuous stream of sealant around the perimeter of the shower tray. If necessary, re-apply sealant to cover up any potential gaps in the surface area.

Step 4 – Smoothen the Surface

Carefully inspect the new layer of sealant to confirm all gaps have been properly covered up.

While the sealant is still wet, use the pointed spatula to smoothen out the solution and make sure it covers the desired area. Be careful not to smoothen the sealant too much or else it may crack or fray. From there, remove the masking tape and use a dry cloth to clean up any excess sealant around the area.

Step 5 – Wait to Dry

Let the new sealant dry for at least 24 hours before you reuse the shower.

Shower Sealed have over 25 years of experience in shower sealing and repairs. To have your shower professionally sealed by the best technicians, call 1300 519 133 for a free quote.

How to Fix Your Leaking Shower Taps

By Shower Sealed | 9th November 2018

Is the constant ‘drip, drip, drip’ of running water starting to drive you insane? When you consider the fact that water is going to waste, it’s no surprise the sound can be irritating – you’re literally hearing money go down the drain!

The good news is, if the leak is caused by a malfunctioning shower tap, you may be able to save money and fix the problem yourself. All you need is a few basic tools, an hour or two of your time, and a basic understanding of how to fix a leaking tap.

What You Need

Below are the following tools you need to get the job done right:

  • Flathead screwdriver
  • Cartridge puller (available at your local hardware store)
  • New faucet tap cartridge (make sure you purchase one that meets the manufacturer standard)

As a handy hint, if you want to avoid losing any tiny screws or parts, place a small sheet over the drain cover.

Step 1 – Check the Shower Handle

Now this may seem obvious.

But it’s not uncommon for a leaky shower to be caused by simply not turning the tap off properly. For this reason, before you start to pull apart your shower components – make sure the handle itself is turned all the way off.

Is the shower still leaking? If so, head on to Step 2.

Step 2 – Turn of the Main Water Supply

Every household in Australia has a water mains switch that lets you cut off the water supply to the house.

Where can you find the water mains switch? Typically they are found at the front of the house near the water meter, most often near the garden tap. Depending on the layout of your house, this could be near a garden bed, footpath, or even buried among a pile of rocks.

Once you’ve found the switch – it may either be a knob or nut for turning – simply turn the device counter-clockwise (to your right) until it’s in the off position.

Step 3 – Remove the Shower Tap

Now comes the first real step to fix your leaking shower tap. First, you need to remove the shower taps and replace the cartridge.

What is a cartridge? Essentially, it’s a mechanical part inside the handle that regulates the flow of water and temperature. Cartridges are made up of many different parts (e.g. the O-ring) and any of them can fail. When this happens, the device loses the ability to maintain water flow and must be replaced.

To remove the handle, use a flathead screwdriver to pry off the handle cap or cover. Beneath this cap is the internal handle screw. Use a screwdriver to remove the internal handle screw.

Step 4 – Remove the Current Cartridge

Once the handle is off, you’ll immediately expose a large ring – this is the cartridge.

To remove the cartridge, you’ll need to use a special device known as a cartridge puller. This tool is specially designed to remove stubborn cartridges and simplify the whole process. Plus, it’s universally designed to work for any kind of cartridge.

Depending on the type of cartridge you currently have, you may need to remove a cartridge clip before you can attach the cartridge puller. From there, simply attach the device – be sure to follow the instruction manual to do this – then twist the puller back and forth while you literally pull the cartridge out.

Step 5 – Install the New Cartridge

By following the same process as above – but in reverse order – install the new cartridge and make sure it’s properly aligned. Re-install the O-ring (or replace it if damaged) and place the handles back in their original position.

Step 6 – Test for Leaks

Finally, turn the mains water supply back on and switch the tap on and off. If there is no water leaking in the off position – the problem is fixed.

Don’t have the time or resources to fix a leaking shower tap on your own? Then you will need to call a local licensed plumber. Should you however have leaking shower from somewhere else then Let the experts at Shower Sealed save you time, money and hassle. To request a free quote, call 1300 519 133 or send your online enquiry.

What is the Best Way to Shower Seal My Shower?

By Shower Sealed | 31st May 2018

It is estimated that 29% of water usage in the average Australian home is in the shower. Every day the shower wall and floor surfaces are exposed to large amounts of water and has to safely guide it down the drain. When water meets a porous tiled surface in a compact area, it’s only a matter of time before a leak occurs and you’ll be asking yourself, “What is the best way to shower seal my shower?”

Before you run to the hardware store, take some time to assess the situation and prepare yourself with the right tools.

Identify the Leak

Water is a powerful force that flows freely in many directions so it can sneak into even the tiniest cracks, gaps and crevices. The design and condition of your shower will determine where the water travels most frequently, how long it takes for the water to drain, and if there is anything stopping the water from reaching its destination.

A quick visual inspection will help you answer most of these questions. The most crucial things to look out for are:

  • Loose, broken or cracked tile grout
  • Deterioration of silicone in the floor and wall junctions
  • Cracked, broken or loose tiles
  • Failure of waterproof membrane below the surface
  • Some harsh cleaning products strip away surface sealants and other coatings
  • Poor installation of tiles, grout or plumbing facilities

What to Look for In Shower Sealant

Before you know the best way to shower seal your shower, you need to use the right products.

Luckily, shower sealer is inexpensive and can be easily purchased at most hardware stores. When applied to a tiled surface, the solution penetrates the grout and initiates a chemical reaction that solidifies after a few hours to help block the passage of water.

Most store-bought products have enough solution in a single bottle to comfortable fill an entire shower. Sealer is also easy to apply and the treated area is ready to use the next day.

Plus, the solution is clear so it will not change the appearance of the surface.

The Best Way to Shower Seal Your Shower

No matter where you apply the sealant, the process is typically the same and involves the following steps:

  1. Remove Old Grout: Gently strip away at the existing sealant with a sharp metal blade until the surface is clear.
  2. Clean Up: Give the tiles a thorough clean to ensure the surface is dry, while being free of dust and debris.
  3. Prepare the Tools: Cut the shower sealant nozzle at a 45° angle, this ensures the sealant is applied evenly along the surface.
  4. Aim and Fire: Aim the product at the desired surface and apply generously along the grout line. For convenience, it’s best to start from the centre of the shower and work your way outwards.
  5. The Finishing Touch: Finally, gently spray water on the newly applied sealant. Take a Popsicle stick, and run it over the surface until its smooth. Be sure to clean up any leftover debris or product.

Still asking yourself, “What is the best way to shower seal my shower?” Avoid the hassle of a potentially messy job and let the experts save you the trouble. Shower Sealed has over 23 years of experience in shower sealing and most services are backed with a 12 year written guarantee. For a FREE quote, call 1300 519 133 and we’ll be happy to arrange an appointment for you.

What You Should Know About Shower Sealing When You Have Tenants

By Shower Sealed | 31st May 2018

In a rental property, the tenant and landlord must work together to resolve maintenance issues and keep the property in good condition during the tenancy agreement. Leaking showers and bathrooms are a common maintenance request and often leave tenants concerned about losing access to the bathroom for several days. Luckily, when you have tenants, shower sealing in most cases will effectively fix those sudden leaks without a major disruption to their current standard of living.

The Importance of Shower Sealing When You Have Tenants

Most shower and bathroom leaks are caused by natural building movement. This is where seasonal changes cause the soil to rise and shrink, which then cause the foundation to gradually shift in unpredictable ways.

Foundation shifts lead to all kinds of property damage and increase the risk of leakage. For example, the gap between the shower floor and wall junctions can widen. Or the tile grout gets heavily compressed and cracks, which exposes gaps for water to travel down.

A trained technician – from a provider like Shower Sealed – can assess the shower and accurately diagnose the cause of the leak using the latest technology. From there, they can effectively reseal the shower, re-grout the tiles, and carry out other repairs to ensure the shower does not leak again.

Reporting a Leaking Shower or Bathroom

It is the responsibility of the tenant to report shower and bathroom leaks when they happen. This way the landlord can review the request and quickly arrange a qualified technician to fix the problem.

But is shower sealing when you have tenants an emergency or routine repair?

According to the Residential Tenancies Authority, ‘a burst water service or serious water service leak’ is considered an emergency repair and the landlord must arrange a tradesperson to inspect the premise within 24-48 hours of being notified of the problem.

Who Pays for the Cost of Shower Sealing?

If the shower or bathroom leak is due to building movement, it is considered to be wear-and-tear and must be paid for by the landlord. However, if the tenant does not notify the landlord of the problem in a reasonable timeframe, they could be liable for the cost of waterproofing and other repairs.

When you have tenants, shower sealing, re-grouting and other preventative measures go a long way to lower more expensive damages caused by leakages. Call Shower Sealed today on 1300 519 133 for a tailored waterproofing solution backed by a 12 year guarantee.

Do I Need to Waterproof My Whole Bathroom?

By Shower Sealed | 31st May 2018

Bathrooms are the main wet area in the house. Therefore, you need to waterproof the area so that water does not get into the substructure of the house and cause major structural damage. Waterproofing is typically done by experts while the bathroom is being built. It involves setting up a waterproof barrier around the floor and walls of the bathroom, including the shower. Do you need to waterproof the whole bathroom? Not exactly. But there are waterproof requirements to be met.

Waterproof Standards for Bathrooms

The Building Code of Australia and Australian Standards (AS 3740-1994) set out the minimum requirements of waterproofing a bathroom. All bathrooms in Australia must comply with these standards, as follows:

  • The entire shower floor must be waterproofed
  • Shower walls must be waterproofed up to at least 1800mm
  • The walls must be waterproofed up to at least 150mm
  • Over the hob or step down must be waterproofed to at least 150mm
  • If the bathroom floor is above ground level, or made of timber, plywood or particleboards, the entire bathroom floor must be waterproofed

Of course, some bathrooms will need to go beyond the minimum standards to be completely waterproof. If your budget allows for it, it is a good idea waterproof the whole bathroom anyway. This will ensure the whole bathroom floor and shower recess is waterproofed.

Another thing to remember is some councils require waterproofing to be done by a licensed waterproof expert to be compliant. Whether you are waterproofing a new or existing building, make sure the tradespeople have the relevant licensing and insurance to carry out the job properly.

Still not sure if you should waterproof the whole bathroom? Call 1300 519 133 for a FREE report on the condition of your bathroom waterproofing.

Types of Bathroom Waterproofing

Waterproofing is done at different stages of building. Some systems are set up before the floors and walls are laid down, and the rest is put in place after everything has been established.

The most common type of waterproofing is the membrane. Before the floor and walls are laid, the surface is cleaned and primed, then followed by the application of a membrane waterproofing agent that is either painted, sprayed, or laid down as a sheet. Spraying and painting are the most common techniques used to waterproof wet areas.

After the floor and walls are established, there are other types of waterproofing set up. Liquid sealant is applied to tiles on the shower wall and floor, which serves as a protective barrier to stop water from breaching the surface.

Silicone sealant is also used to seal gaps between the floor and wall joints. Overall, these combined systems help waterproof your whole bathroom.

What if My Existing Bathroom Needs Waterproofing?

If you have found a shower or bathroom leak, you may be able to fix the problem without ripping up the tiles.

Waterproofing is a technical procedure and should be carried out by a licensed and insured expert. A qualified service will be able to repair and restore many aspects of the shower with exclusive products, tools and procedures, which offer superior water-resistance to store-bought products.

Most services are also backed with a 12 year written product guarantee.

Tired of asking, “Should I waterproof my whole bathroom?” Get the answers you need with a free consultation from Shower Sealed. Call 1300 519 133 to book your appointment today!

How Much Damage Can a Leaking Shower Cause?

By Shower Sealed | 31st May 2018

This is a question that is often asked by homeowners, renters, and landlords. For good reason too! Leaking showers and bathrooms are a common issue for homeowners and something that tenants and estate agents will face at least once in a rental property. Most people know these kind of leaks are bad news. But due to the discreet nature of the problem, it can be hard to tell just how much damage a leaking shower can cause.

The type of damage you can expect from a leaking shower will vary. Water can penetrate the surface in a number of ways whether it be through a broken or loose tile, hole in the grout, or a split silicone joint.

It does not matter how the water leaks. It will eventually enter an unknown part of the house that is not designed to handle moist conditions (the substructure) – and that is where the trouble starts.

But how do you identify the signs of a leaking shower? And what kind of damage will the leak cause?

Signs of Damage Caused By a Leaking Shower

Signs of damage from a leaking shower come in two forms: things you can see (or smell), and things you cannot see. The latter is of course harder to identify and narrow down the source of the problem. These kind of issues can also be more serious and lead to an underlying issue with the internal plumbing.

Just how much damage can a leaking shower cause? Here are the most common visual signs of damage:

  • Peeling, flaking or chipped wallpaper
  • Damp carpet near or around the bathroom
  • Water marks on the ceiling below the shower
  • Musty fumes or odours
  • Mouldy silicone joints
  • Loose, cracked or damage tiles
  • Missing tile grout
  • Paint bubbling on the walls
  • Cracks in the walls
  • Visible gaps in wall and floor joints
  • Hard to open certain doors or windows

Tired of asking yourself, ‘How much damage can a leaking shower cause?’ Call Shower Sealed on 1300 519 133 to find out, and fixing your leaking shower for good.

Damage to the Property

Besides these obvious warning signs, a leaking shower can cause much more serious damage.

When water breaches the substructure of the home, it can create damp conditions in the foundation and encourage the growth of mould or mildew. If left to grow, this can pose a serious health hazard to the family, and trigger a reaction from people with existing respiratory problems.

Damp conditions can also attract timber pests and you could end up with a serious infestation on your hands.

Most materials that form the foundation of a home are not waterproof. When exposed to water; timber products like floorboards, wooden joists, beams, and bearers will start to rot and weaken to the point it could collapse.

Need to Fix a Leaking Shower? Call the Experts

Clearly, leaking showers are more than just a nuisance.

If left unchecked, shower leakage can cause serious damage to your property and pose a major health risk to your family. Serious leaks can also take days to repair, and leave you without a bathroom for up to a week – what an inconvenience!

The good news?

Most shower and bathroom leaks can be fixed without the need to remove tiles and replace the membrane. Local waterproofing experts offer a range of hassle-free repair and renovation services to stop all kinds of leaks at a minimal cost. If you are concerned about your leaking shower, request a consultation with a waterproof expert who can assess your shower and find the source of the leak.

Most service providers offer a 10+ year guarantee (Shower Sealed offer a 12 year guarantee) on their waterproofing services.

Let Shower Sealed fix your leaking shower, and put a stop to the leak! For peace of mind, call Shower Sealed on 1300 519 133 to request a FREE quote.

How to Stop a Leaking Shower

By Shower Sealed | 27th March 2018

A leaking shower can become a huge problem if water penetrates the surface. Not only does excess water increase your utility bill – moisture can damage the supporting structure and pose a health risk to friends, family and tenants.

To avoid spending possibly thousands of dollars on home repairs, you should call a plumber or waterproofing expert to fix your leaking shower. A visual inspection can reveal signs of damage and identify what needs to be done.

Whether you hire a professional who try to solve the problem yourself, here’s how to stop a leaking shower.

Replace Cracked or Broken Tiles

Cracked tiles provide an entryway for water to penetrate the surface and enter the supporting structure of the house.

These should be fixed or replaced to prevent moisture damage from encouraging mould growth or weakening the timber support structure.

Look for spare matching tiles in your property or get custom tiles to match the size and look.

Replace Tile Grout

Grout is used to secure bathroom tiles and seal the gaps between each tile. Grout is not waterproof and over time, it will wear down and start to crack or crumble.

When the grout cracks get large enough, they should be replaced with a cement-based grout containing biocide to resist mould and bacteria. To remove the old grout, clean and dry the surface, then use a power tool or manual extracting knife to ‘lift’ the grout from the gap.

Replace Movement Joints

Movement joints are silicone-based joints that establish a watertight seal between the wall and floor junctions in the shower. Sometimes, these joints are flexible silicone strips that allow room for building movement without degrading the watertight seal.

If your silicone joint has become loose or degraded, replacing them is one way you can stop a leaking shower. Simply remove the old joint and prepare the surface by cleaning, drying and applying anti-mould treatment to the surface.

Finally, install the new silicone strip and allow it to settle before using the shower again.

Clean the Shower Head

Sometimes knowing how to stop a leaking shower can be as simple as replacing a faulty shower head. These can leak when the inner seal becomes worn or the parts get clogged with debris.

First, turn off the main water supply and remove the showerhead by unscrewing it from the pipe with your hands. Showerheads don’t get removed often so they may not come off easily. If so, use pliers or an adjustable wrench to release the showerhead.

If the current showerhead can be salvaged, give the interior of the showerhead a thorough clean and remove any mineral deposits disrupting the flow of water. If the washer or o-ring has been worn down, replace it, and reinstall by wrapping the threads of the pipe stem with durable thread seal tape.

If the current showerhead is too damaged or worn down, replace it with a new one and check for leaks after being installed.

Still not sure how to stop a leaking shower? Get expert support from a waterproofing specialist. Call 1300 519 133 or make an enquiry to get a FREE quote and advice.

What to Do in Leaking Shower Emergencies

By Shower Sealed | 27th March 2018

Leaking showers pose a number of problems for homeowners, landlords and property managers.

If left untreated, leaking showers can damage the property, increase water bills, and create a health hazard for friends, family and tenants.

There are many reasons why showers leak and it’s not always clear where the problem is coming from. To solve the problem correctly, call a leaking shower specialist to identify the problem and get long-term treatment to save you from heartache later on.

In the meantime, here’s what you can do to control the situation until an expert arrives:

Look for Water Stains

Water stains can occur in many parts of building depending on if the shower itself is leaking or the plumbing is faulty elsewhere.

Most stains in the ceiling are caused by slow leaking shower emergencies in the upper level. This happens when water penetrates the tiled surface and starts to dampen the substructure. If you find stains on interior walls around the home, the pipes could be leaking elsewhere on the property.

However, don’t assume that all stains are caused by faulty plumbing alone. For example, if you’ve been having a lot of rain lately and discover a water stain, your rooftop could be leaking.

Identify and Remove Mould

Mould growth is a major concern during leaking shower emergencies.

Mould thrives in damp, moist areas and when allowed to grow, produces allergenic substances that cause allergic reactions from sensitive people such as red eyes, skin rashes, sneezing and hay fever. In serious cases, mould can trigger asthma attacks and irritate the skin, nose, eyes, and cause respiratory problems for the throat and lungs.

If you find mould in the bathroom or anywhere else inside the property, have it removed and get in touch with a waterproofing expert who can solve your leaking shower issues.

Remove and Replace Tile Grout

Over time, building movement can put pressure on tile grout causing it to wear down, crack or crumble. The exposed tile grout could let excess water into the substructure and result in water damage.

If you have the knowledge and tools, you can replace the old tile grout with new grout to establish a fresh new seal.

Clean or Replace the Showerhead

Some shower leaks can be fixed by maintaining the showerhead.

By removing the showerhead, you can clean the interior parts and remove any debris that may be disrupting the flow of water. If the showerhead is too worn out, you can replace it and see if that solves the problem.

To have your leaking shower emergency solved by a waterproofing expert, please call Shower Sealed on 1300 519 133 and request a FREE quote. Our unique combination of Ultra Bond Technology can provide lasting relief from leaking showers – without the need to remove tiles.

Do You Need to Remove Tiles to Repair a Leaking Shower?

By Shower Sealed | 27th March 2018

The three major concerns that people have when they find out their shower is leaking are:

  • How much will it cost to fix?
  • Has my property suffered any damage?
  • Do I need to remove tiles to repair my leaking shower?

Whether or not your tiles need to be removed depends on where the leak is coming from.

Most leaks are caused by building movement, which causes the tiles, grout or silicone to disintegrate. However, you should not jump to conclusions until you know that is the exact problem, or else you waste time and money focusing on the wrong issue.

Fortunately, there is a simple test you can do to find the source of the leak.

The Hob Test

The purpose of the hob test is to find out if water is escaping from the shower.

For this test, you must apply duct tape to the shower drain and fill the shower hob with water. Once you’ve reached the top of the hob, mark it with tape and wait at least 20 minutes to see if the water level drops.

If so, then water has likely escaped through a broken tile or grout. If not, the leak could be coming from elsewhere, and you should have a plumber inspect the pipes to find any leaks in the internal plumbing.

Luckily, there are ways to repair your leaking shower without the need to remove any tiles.

DIY or Professional?

Once you’ve found the source of the problem, you can either try to repair your leaking shower yourself or hire an expert to do the job.

The DIY route can save you money, if you know how to fix the problem correctly. But a poor maintenance job will cause you a lot of frustration, and allow the current water damage to get even worse – which’ll cost you even more money to repair!

If you’re not the sharpest tradie on the block, there’s no shame in getting a waterproofing expert to fix your leaking shower.

Why Choose a Waterproofing Expert

In most cases, a professional service can repair a leaking shower without the need to remove tiles.

Unlike replacing the waterproof membrane (which can take up to a week), the job only takes 2-4 hours and the area can be used the next day. Most importantly, you get peace of mind with a 12-month guarantee to protect you from further leaks.

To inspect the shower, a waterproof technician will use a special leak detector and thermal image camera to accurately diagnose the source of the leak. From there, they will replace any broken tiles, regrout the floor and joints, and completely reseal the shower surface with a powerful sealant to establish a waterproof barrier.

One thing you cannot buy with a DIY approach is peace of mind. Most professional services offer a workmanship guarantee that protects you from the risk of water leakage. If the shower leaks again within the warranty period, it won’t cost you anything to fix the problem.

Do you need a professional to repair your leaking shower? Shower Sealed can get the job done without removing ANY tiles. Call Shower Sealed on 1300 519 133 to request a FREE quote today!

Can Tile Regrouting Stop Your Shower From Leaking?

By Shower Sealed | 27th March 2018

Showers are the most commonly used wet area in the house. To prevent water from getting into unwanted parts of the home, it’s important the waterproofing system works in perfect harmony to achieve this goal.

However, not all shower components do this equally and wear-and-tear will compromise the system over time. If you’re asking yourself, “Can tile regrouting stop my shower from leaking?” This guide can help you find the answer.

Understanding the Basics of Grout

Typically made from a mixture of cement, water and sand, the combination of grout and sealant creates a watertight seal between tiles to stop water from breaching the surface.

That means tile grout is essentially waterproof, right? Not exactly.

While grout offers great stability in wet conditions, the unique formation of rocks and minerals means the material is quite porous. Grout is also susceptible to building movement, which compresses the material to reveal cracks, splits and pinholes – thus increasing the risk of potential leaks.

It’s not all bad news though, and tile grout does serve an important purpose. While grout isn’t waterproof, it is moisture-proof so condensation cannot travel from one side to the other.

Naturally, this condensation will evaporate throughout the day until the grout is dry.

Can Tile Regrouting Stop a Leaking Shower?

Whether or not replacing the tile grout will stop your leaking shower depends on the exact source of the leak.

Most showers leak when water enters the substrate of the property through cracks in the tiles, damaged grout or broken sealant barriers. It goes without saying, but these concealed parts of the home don’t cope well with moisture. When the conditions become damp, it not only causes serious damage to the property and encourages mould growth – but also attracts termites into your home.

If you have any clear defects on the shower surface, tile regrouting will probably fix your leaking shower.

How to Regrout Your Shower

Regrouting your tiles is a fairly quick and simple job. Plus, you don’t have to remove any tiles to do it.

First, you must remove the existing grout. This job can be done faster with a special grout removal tool, power grinder or cartridge blade. Cut away the grout to at least half the length of the tile.

Next, thoroughly remove any leftover grout or soapy discharge remaining on the surface. Then use a grout float to apply the new grout at a 45-degree angle. Be sure to smoothen out the surface until there’s no gaps or air bubbles.

Finally, wipe away the excess grout and apply grout sealer to further enhance their appearance and stability in wet conditions.

Don’t Have the Time, Resources or Skills? Hire the Professionals!

Shower Sealed offers you peace of mind with a 100% waterproof seal and the assurance of a 12 year guarantee.

With a combination of exclusive tools, products and procedures, Shower Sealed can 100% seal your shower in less than 4 hours. By using exclusive Ultra Bond Grout, you achieve a far superior watertight seal that lasts longer than conventional store-bought products.

There’s no need to remove tiles, and the area is ready to use the very next day. After the job is done, your shower will look fantastic and enjoy years of lasting protection from water damage.

Call Shower Sealed on 1300 519 133 for a FREE quote.

7 Steps to Fix Your Leaking Shower

By Shower Sealed | 27th March 2018

Leaking showers are a minor inconvenience that can cost you a fortune if the problem is ignored.

Every drip from the leaking faucet will gradually raise your water bill. And if it’s leaking hot water? Expect to see more zeros on that energy bill too. Leaking showers can also cause major damage to the property.

Don’t wait for your leaking shower to become a major hassle. Here’s 7 easy steps to fix your leaking shower.

Step 1 - Faulty Shower Faucet

Shower drains aren’t the only section where water can escape from.

Below are some of the most common causes of water leakage:

  • Blocked or corroded showerhead
  • Faulty shower faucet
  • Missing sections of tile grout
  • Broken tiled floor or wall
  • Degraded silicone between wall/floor joints
  • Failing waterproof membrane
  • Damaged or loose pipeline
  • Interior plumbing fault

Most of these issues can be identified by visually inspecting the shower itself. Any defects on the tiled wall or floor surface will be easy to spot including cracked grout, broken tiles or missing silicone.

However, more serious problems with the interior plumbing will need to be inspected by a professional.

Step 2 - Repair the Shower Faucet

Most shower faucets fail when the O-ring degrades and can no longer control the flow of water. Other common issues occur with the internal washers, valves and temperature stems.

Use a screwdriver to open the faucet and replace any parts that look worn out, corroded or degraded. Test the water after each replacement. The water shop stop flowing almost instantly after the supply is cut off.

Step 3 – Replace the Shower Head

Over time, shower heads will degrade and collect hard mineral deposits that interrupt water flow. You could replace individual parts to fix the leaking shower, but it’s faster and just as cost-effective to replace the entire unit. In fact, some individual shower heads can be purchased for as little as $25.

Replacing a shower head is quick and easy. Wrap an adjustable wrench around the head and turn counter-clockwise until it’s loose enough to remove. Get rid of any excess materials, wrap thread sealed tape (Teflon) around the threads of the pipe, and install the replacement head.

Test the water. If leaking persists, try tightening the shower head more until it stops.

Step 4 - Replace Broken Tiles

Got any cracked, chipped or broken tiles on the shower surface? Until you fix or replace them, your shower will keep leaking.

Head down to your local hardware store and purchase new tiles that match your existing set. Depending on the condition of the tiles – particularly if water is leaking below – they might already be loose and easy to remove. Otherwise, use a chisel to break out the tiles into smaller pieces.

Ensure the surface is smooth and clean before installing the new set. Lay down ceramic adhesive or tile cement and place the tile itself down – gently apply pressure. Finally, wait until its dry then apply grout to create a watertight seal.

Step 5 - Regrout Shower Tiles

Grout is not a waterproof solution. But it does fill the gap between your tiles and ensures a smooth professional finish. When fixing a leaking shower, be sure to replace worn out, cracked or split grout old grout that has worn out, cracked or split. Even the tiniest holes are enough for water to breach the premise.

Use a scraping tool to remove old grout, and wipe down the surface with a damp sponge to ensure it’s clean. Regrout the whole tile with a grout float, then let it dry for at least 20 minutes. Finally, wipe the excess grout off the face of the tile, and vacuum up debris left on the ground.

Step 6 - Silicon the Gaps

Silicone sealant fills the gap between wall and floor joints between shower screens, basins and bathtubs.

Old silicone will become mouldy, cracked and discoloured. If left untouched, it’ll eventually get loose and allow water to enter unwanted places. Thankfully, it’s easy to replace your old silicone with a new watertight layer.

Apply silicone remover to the current layer and give the solution 2-4 hours to soften the silicone. Use methylated spirits to remove the old silicone and ensure the surface is smooth, clean and dry.

Lastly, apply the new silicone sealant to the exposed gap. Allow to dry for at least 2 hours before using the shower.

Step 7 - Reseal the Shower

Shower sealant is a silicone treatment that penetrates tile grout to form a permanent waterproof barrier. The substance prevents water from escaping through the grout and offer long-term protection from water damage. Without the need to remove tiles, you can reseal the entire surface and fix your leaking shower for good.

There are commercial products you can buy off the shelf to reseal the shower. But for peace of mind, we recommend hiring a professional to do the job. A waterproofing specialist will identify the exact cause of the leakage and use specialised tools and products to resolve the problem.

Better still, you get a 12 year waterproof guarantee with every service!

Call Shower Sealed on 1300 519 133 or send your enquiry to request a FREE quote.

7 Common Causes of Leaking Showers

By Shower Sealed | 27th March 2018

One of the biggest causes of stress for a homeowner is finding out the shower is leaking.

Most leaks are caused by building movement and foundation shifts. These occurrences happen naturally over time, but can be accelerated due to extreme temperatures and the decay of building materials. Building movement places stress on many components of the shower and waterproofing system. Tile grout can crack, the waterproofing membrane can lose its adhesiveness, and the gap between wall and floor joints can widen – leaving it exposed to water breaching.

Leaking showers can cost you time, money and heartache. Leaking water can send your bills skyrocketing. If water enters the substructure of the home, it can moisten the timber support structures, which attracts termites and weakens the structural integrity of the building.

Finding the cause of a leaking shower is essential. Even if you plan on hiring a waterproofing professional, you could save money by finding the source of the problem yourself.

Here’s 7 of the most common causes of a leaking shower:

1. Cracked Tile Grout

If there’s cracked or missing grout between the tiles, water could be leaking through the exposed gaps.

Do a small test to find out if this is the case. Spray water on isolated sections of the wall and let the surface dampen. If you notice any cracks, splits or holes – not matter how small they may be – you need to re-grout these sections.

Replacing the tile grout is easy. You can buy pre-mixed grout, apply it yourself, and scrape away the loose material.

2. Faulty Shower Faucet

Leaking shower faucets are one of the most common causes of leaking showers. They can waste litres of water and disrupt your day with their nagging drip, drip, drip sound.

Shower faucets are prone to degradation after years of regular use. O-ring cartridges can become worn and no longer be able to control the flow of water. Hard mineral deposits can clog the internal components and leave them corroded.

To identify the problem, turn of the main water supply and disconnect the faucet with an adjustable wrench. Inspect each component, and replace any parts that are damaged or worn out.

3. Leaking Drains

All shower drains are connected to a P-trap, which is designed to stop debris from forming deep clogs in the plumbing system.

Over time, a P-trap can become disconnected from the drain or cracks can form below the fixture. This causes the water to leak into the substructure of the property. Eventually, this’ll produce visible stains on the lower level ceiling.

If you suspect a failure in your plumbing system or drainage, you will need to call a professional.

4. Waterproofing Failure

Waterproofing membranes are a legal requirement for wet areas in the home. They’re the single most important protective barrier that prevents shower leaks.

Most causes of waterproofing failure are due to poor workmanship. Often this is due to time constraints, which means not enough time is spent to prepare and prime the surface to ensure a watertight seal. If the surface has obvious warping and distortion, the membrane won’t adhere properly and will eventually need to be replaced.

If a failed waterproof membrane is causing the shower to leak, you’ll have to go a few days without the shower. Why? Because it’s a long process and the tiles need to be removed then eventually re-installed.

5. Silicone Degradation

Silicone is designed to prevent water from breaching the gap between the wall and floor joints.

Unlike tile grout, silicone can withstand the stress of building movement and foundation shifting. However, they can become cracked, mouldy or loose after regular exposure to wet conditions.

To replace the silicone, remove the old silicone strip and remove any leftover residue. Ensure the surface is dry, apply the new silicone to the gap then allow to dry before re-using the shower.

6. Silicone Degradation

While rare, the cause of some leaking showers is due to their design.

Sometimes the shower screen is placed on the wrong side of the job. Instead of being installed on the inside of the hob, it sits near the edge of the other side – leaving a short shelve on the inside of the shower.

This causes the water to slide down the shower screen then land directly on the hob and tile grout. Eventually, water penetrates the grout and causes water damage below the tiled surface.

There’s not much you can do about a poor shower hob job. However, a professional resealing service can prevent the risk of water penetrating the surface and causing serious damage.

7. Tiles Need Resealing

Every shower is treated with silicone sealant to form a protective barrier over the tiled surface.

Over time, shower sealant can degrade and will need replacing. If your tiles aren’t damage and the grout doesn’t need replacing, a simple resealing job can prevent water from breaching the surface. In most cases, resealing only takes a few hours and there’s no need to remove any tiles.

Afterwards, you’ll have peace of mind knowing your home is safe from the threat of water damage.

Shower Sealed offer unique waterproofing solutions to stop leaks without removing any tiles. Call 1300 519 133 or send details about your problem to get a FREE quote.

The Hidden Dangers of DIY Shower Repairs

By Shower Sealed | 27th March 2018

At an early age, we’re told how important it is to be independent and look after ourselves. Whether it’s learning how to tie our shoes, cook an exceptional meal or drive a car, we take pride in our ability to learn new skills and overcome life’s many challenges.

However, there are times where it’s safer and more efficient to hire a professional.

Unless you’re an experienced mechanic, you probably wouldn’t try to replace your own brake pads or install a new carburettor. And you probably wouldn’t risk trying to service the electrical switchboard in your home.

The same goes for your household shower.

Here’s why you should think twice before starting your DIY shower repair job.

Why Professional Waterproofing is Important

Second only to the kitchen, the bathroom uses the most amount of water in the home.

Whether you’re having a bath, shower or using the basin, the plumbing and waterproofing system is specially designed to control the flow of water and stop water from getting into places it shouldn’t be.

This is achieved by apply waterproof membranes beneath the tiles in potential wet areas such as:

  • Inside the shower hob and surrounding area
  • Around the bathtub, basin and cabinetry
  • General tiled walls and floors
Afterwards, the tiles are laid down then sealed with tile grout while gaps between the wall and floors are secured with a non-corrosive sealant.

The Risks of DIY Shower Repairs

Showers rely on a secure connection of pipes and moving parts to provide a safe and consistent flow of water. You need a good amount of technical knowledge to know how to repair and replace these parts. If you don’t have much experience in DIY shower repairs, you risk damaging the internal components or not installing a new part correctly.

If there is a damaged pipe or faulty connection, water can penetrate the substructure of the property and cause serious damage to the internal support structure. Not only are these repairs expensive, you could be left without a shower for several days or weeks!

Another problem is that many over-the- counter products are silicone-based. These products only provide temporary relief from leaking showers and end up going mouldy after a few months.

So, unless you have the right products and are 100% confident in your DIY shower repair skills, you should trust a licensed professional to fix your leaking shower instead.

The Shower Sealed Difference

At Shower Sealed, we have over 25 years of experience in shower sealing, repairs and renovations.

Our team has a deep understanding of household plumbing and the common signs of leaking showers. Using our local expertise and technical know-how, we can identify your leaking issue and provide a no-fuss solution at an affordable cost.

Unlike over-the- counter products used in DIY shower repairs, which are usually silicone-based and only provide temporary relief, we use Ultra Bond Technology to target and stop all leakage points in the shower.

With a combination of exclusive tools, products and procedures, Shower Sealed can effectively seal any leaking shower without the need to remove tiles. Most service appointments take 4 hours and the area can typically be used the next day.

Need us to replace the showerhead, faucet, washers or O-rings? No problem.

Our team has access to shower parts for a range of shower types, so we can do onsite repairs and replacements quickly. If that wasn’t enough, most of these services come with a 12 year guarantee.

What could be better than that?

Don’t take the risk with a DIY shower repair job. Call Shower Sealed today on 1300 519 133 or send an enquiry to get a FREE quote.

5 Ways to Stop Your Shower Leaking

By Shower Sealed | 27th March 2018

Can you hear that dripping sound?
It’s not just the sound of water going down the drain. It’s your hard-earned cash going into
the pockets of your water company, plumbers and – if the problem is left for too long – the
builders who need to repair the property due to moisture damage.

If you’re left wondering, “How can I stop my shower leaking?” There are options.

An in-home inspection from Shower Sealed can help you discover the problem and find out
the best treatment to suit your individual circumstances. They can also professionally fix and
replace any faulty parts so you can enjoy a safe, reliable source of water.

If you’d rather take the DIY approach, there’s a few cost-effective ways to stop a leaking shower.

1. Fix the Showerhead

Most faulty showerheads leak when the washer or O-ring breaks down and can no longer
stop water from passing through. The internal parts can also become blocked from dirt,
grime, grit, mineral deposits and lime scale.

To remove the showerhead, do the following tasks:

  1. Turn off the main water supply (be prepared for leftover water after removing the
    showerhead)
  2. Unscrew the showerhead from the pipe with your hands. If the showerhead is stuck,
    use an adjustable wrench or pliers to loosen the connection.
  3. Inspect the washer and O-ring. If they appear dry, brittle or worn down – replace
    them.
  4. Combine a mixture of water and vinegar then bring the solution to a boil. Dip an old
    toothbrush in the mixture and gently scrub the showerhead to remove any dirt, grime, grit, lime scale, and mineral deposits that may be clogging the showerhead
    holes.
  5. Re-secure the connection between the showerhead and pipe with thread seal tape.
  6. Turn the main water supply back on. Test the shower and inspect for any signs of leakage.

2. Fix the Faucet

If fixing the showerhead does not stop your shower leaking, the problem may be coming
from the faucet.

Shower faucets come in one-knob and two-knob configurations. If your shower has a two-
knob switch, you’ll need to inspect and replace both valves at the same time.

After turning off the water supply and disassembling the faucet, inspect the washers for the
build-up of dirt, grit, grime and mineral deposits. If the washers are beyond repair, save
yourself the trouble and replace them or hire a professional to do the job for you.

3. Replace Broken Tiles

A loose or broken tile will increase the chance of moisture damage to the property.

Inspect the surface of your shower and fix or replace any broken tiles. Be sure to keep the
area clean when installing the new tiles and consult your local hardware store to find tiles
that match the existing set.

If you’re struggling with removing the tiles or applying new grout, a waterproofing expert
can do the job for you and stop your shower leaking.

4. Re-Grout the Tiles

Are the tiles are in good condition but the grout is worn down?

Remove the current grout by using a grout removal tool or power tool with an oscillating blade. Avoid making contact with the surrounding tiles and always wear safety goggles to protect your eyes. Once most of the grout has been removed, use sandpaper or a grout saw to remove leftover grout and make the finish smooth.

From there, you can apply the new layer of tile grout to the surface. Use a grout float and apply the new layer at a 90-degree angle, sweeping the float diagonally across the surface.

5. Hire Shower Sealed to Fix Your Leaking Shower

Is the DIY route not getting the results you want? Call Shower Sealed for effective and long-lasting relief from leaking showers.

Shower Sealed are the experts in shower sealing, re-grouting, tiling, shower repairs and renovations. Without the need to remove tiles, your shower can be serviced within 4 hours and be ready to use the next day.

The unique combination of Ultra Bond Technology makes it possible to seal your leaking shower. All tools, products and procedures are designed to target and stop leakage points while making sure your shower looks fantastic.

Each service comes with a 12 year guarantee for peace of mind.

Request a FREE quote and stop your shower from leaking today! Call 1300 519 133 or send your enquiry to get friendly support from licensed professionals.

Why Choose Shower Sealed?

By Shower Sealed | 15th November 2017

Shower Sealed, Shower Sealed Gold Coast & Shower Sealed Brisbane are the number one shower sealing and shower repair company in Queensland.

You can trust Shower Sealed as your local professionals.

With over 23 years of experience within the shower sealing & repair industry we are confident that we can provide you the right solution to seal, repair and or enhance your leaking showers and or bathrooms.

Exclusive Ultra Bond Technology allows us to seal up to 95% of leaking showers without the need to remove tiles. Which intern saves you time, money and hassle?

Shower Sealed also provide full waterproofing, tiling, and or shower renovation services as needed. We will provide you with the right advice from a perspective of total industry professionals.

Most our services are backed with a written 12 year product guarantee.

Shower Sealed offer free of charge onsite inspections and quotes throughout Brisbane, Gold Coast, Tweed Coast to Ballina in NSW’s.

Team at Shower Sealed who perform our quotes have literally seen thousands upon thousands of leaking showers prior to coming to your valued property.

We are very grateful to be used and recommended by Real estates, property and Strata managers, plumbers, pest inspectors, builders and families across Queensland.

We trust that our team can be of service to you and or your clients in the near future.

Call Shower Sealed, Shower Sealed Gold Coast & Shower Sealed Brisbane today on 1300 519 133 or visit our website at www.showersealed.com.au

10 Quick Tips About Shower Sealing

By Shower Sealed | 7th November 2017

So you’ve just found out your shower is leaking and you want to reseal it. Fantastic! Poorly sealed shower trays are one of the most common causes of leaking showers.

In this handy guide, you’ll learn 10 tips about shower sealing to achieve a professional watertight seal.

  1. Look for Signs of Water Damage

    If you’ve discovered your shower is leaking, it’s a good idea to inspect the property to find any signs of damage. Common signs of damage include gaps in floor and wall joints, watermark stains on the ceiling, paint bubbling on the walls, discoloured shower tiles and mouldy silicone.

    All of these warning signs are a good indication that your shower is leaking.

  2. Watch Out for Damp Carpet and Unpleasant Odours

    If water has entered the substructure of the home, the lack of insulation means the water won’t evaporate and will cause the wood to rot or decay.

    This will eventually affect the carpet and leave behind damp spots, along with an unpleasant odour and the growth of mould.

  3. Replace Broken or Cracked Tiles

    Cracked, loose or exposed tiles can direct water to unwanted places in the home. Inspect each tile in your shower and replace them yourself or find a professional installer who can match the style of your current décor.

    Keep in mind this may not solve the underlying issue with your leaking shower. Therefore, it’s recommended you have the premise inspected by a licensed professional.

  4. Make Sure the Area is Clean and Dry

    Now that you’ve inspected the premise, you’ll probably want to re-grout or reseal the shower.

    If you choose to do either of these jobs yourself, make sure the area is clean and dry. This will ensure any product you apply adheres correctly and will save you from the hassle of fixing a poorly done job.

  5. Get a Free Pressure and Moisture Test

    Most professional waterproofing companies offer a free moisture and pressure test.

    A moisture test will identify areas in the home that contain unusually high levels of moisture, while a pressure test will search for defects in your home plumbing. By having these tests done, you’ll get professional tips on the right shower sealing solution for you.

  6. Replace the Tile Grout

    Grout is a silicone-based product used to seal joints between shower tiles. Over time, tile grout will degrade and need to be replaced.

    You can choose to remove and reseal the grout yourself. But if you want to save time and have it done right the first time, hire a licensed professional. They’ll know how to correctly perform the procedure and form a 100% seal to extend the life of your shower.

  7. Remove Old Grout Before Applying the New

    You can apply new grout over an existing layer, but the results are usually not good. That’s because the old grout won’t adhere properly to the new layer and will struggle to maintain a 100% seal.

  8. Replace Wall and Floor Joint Strips

    Building movement places a lot of stress on your home. When it comes to your wall and floor joints, the silicone strip that keeps them connected may fail and expose the substructure to water breach.

    Be sure to replace these strips regularly and check other areas of the bathroom such as tiled surfaces, bench tops, splashbacks, and movement joints.

  9. Reseal the Shower Tray

    Need a new application of silicone sealant on the shower tray?

    Use a high-quality sealant designed for bathrooms and has anti-fungal additives. Make sure you choose a sealant that’s non-abrasive to your kind of shower tile.

    If you’re resealing the shower tray yourself, be sure to follow the instructions and prepare the surface, apply the silicone evenly along the tray, and wipe the excess silicone away with a paper towel.

    Should the shower continue to leak then you should seek advice from a professional?

  10. Hire a Professional Leaking Shower Expert

    If you don’t have the time, tools or resources to properly fix your leaking shower, a licensed professional can offer you professional tips about shower sealing and a cost-effective solution.

    Whether you need grout stripped from the wall and replaced, cracked tiles need repairing or you need sealant applied to the entire floor area – a licensed professional will ensure your shower is 100% seal in every aspect.

My Shower is Leaking – What Can I Do?

By Shower Sealed | 7th November 2017

You were just walking towards the bathroom, when suddenly everything went wrong.

What started with a few pockets of air bubbles in the paint, turns into a sequence of bizarre events – the bathroom door gets jammed, the shower tiles are cracked and discoloured, and a musty odour lingers around the place.

It’s not until you walk downstairs when your worst fears are confirmed; a watermark in the ceiling below the bathroom.

You cry, “My shower is leaking!”

Leaking showers are a common problem among homeowners. But it’s crucial you act quickly to avoid paying for structural damage and exposing your family to mould or bacteria.

Fortunately, there are ways to fix the problem without removing tiles or costing you a fortune.

Confirm the Damage

If you’ve found any of the signs of leakage mentioned above, your shower is most likely the culprit.

However, to avoid heading in the wrong direction for treatment, go over this checklist to confirm the problem actually is a leaking shower:

  • Damp or wet carpet areas
  • Cracked, loosened or discoloured bathroom tiles
  • Tile grout is cracked or crumbling
  • Harsh odours or smells
  • Watermarks on the ceiling below the bathroom
  • Air bubbles in the interior paint
  • Exposed gaps between the wall and floor junctions
  • Certain doors or windows are hard to open
  • Termite activity near the bathroom

In most cases, if you have one or more of these issues, then your shower is probably leaking.

Identify Possible Leakage Points

So you’ve found the problem, but you need to get to the source.

First, look in the shower and assess the condition of your tiles, tile grout and silicone stripping. Are the tiles cracked, broken or loosened? Is the silicone strip peeling off? Is the tile grout crumbling away?

Make sure to look carefully, even the tiniest cracks will allow water to penetrate the substructure of your home. If you can’t seem to identify any faults in the shower, the problem could be more serious like a broken drainage pipe or faulty waterproof membrane.

In any case where you’ve identified a shower leak, a licensed professional can provide a cost-effective solution to 100% seal your shower.

Trust Shower Sealed

At Shower Sealed, we can waterproof your shower without removing any tiles. It only takes 2-4 hours to treat your shower, you get a 100% waterproof seal, and you can use your shower the next day.

All of this comes to you with incredible value for money and a 12 year guarantee.

What could possibly be better than that?

If you’re asking yourself, “My shower is leaking! What can I do?” Call 1300 519 133 or make an enquiry to have your leaking shower fixed in a matter of hours.

What You Need to Know About Regrouting Your Shower

By Shower Sealed | 7th November 2017

Tile grout is one of many materials designed to protect your shower or bathroom from leaking water.

Made from water, cement and sand, tile grout seals the gap between the tiles in your shower. This seal stops water from getting into places around the home that shouldn’t be exposed to moisture.

Once grout starts to crumble, crack or get discoloured, this protective barrier breaks down and leaves the surface exposed to water penetration. Just like any material exposed to the harsh elements, tile grout needs to be replaced so that water can travel to where it belongs – the drain.

If you want to avoid paying a costly repair bill, regrouting your shower is the best way to preserve the quality, structural integrity, and value of your home.

How to Remove Grout

Before taking out your current grout, make sure the area is clean and dry. Give the shower a thorough sweep and clean up any excess debris.

Unless you want to spend hours digging away at old grout, use an electronic multi-tool with a blade attachment specially designed to remove grout. Switch on the tool and gently guide the blade to cut away sections of grout. You don’t need to apply much force – the blade will do the work for you.

To remove excess grout, use a flathead screwdriver to scrape the surface and clear the mess with a vacuum cleaner.

How to Apply New Grout

Before applying new grout, give the area a sweep and make sure the surface is dry. For peace of mind, lay down a clear sheet across the floor and secure the edges with masking tape.

What is the most effective type of grout?

For best results, a polymer-modified grout will provide a more durable and better looking seal. Why? The polymer improves the grout’s water-resistance. And it increases the grout’s flexibility when it comes to building movement and changing weather conditions.

To install the new grout, apply it at a 45-degree angle and work it thoroughly in-between the gaps of each tile. There should be no air bubbles or gaps present after the job is done.

While the grout is still wet, use a wet sponge to thoroughly clean any excess from the surface. You may need to regrout and clean the shower multiple times to achieve a 100% watertight seal.

Save Time With a Professional Regrouting Service

Don’t have time or resources to regrout the shower yourself? Shower Sealed can help.

With over 25 years of experience in the industry, we can give your shower a fresh look and improve its durability for many years to come.

Call 1300 519 133 or make an enquiry to have your shower regrouted by a licensed professional.

Why Should I Waterproof My Shower?

By Shower Sealed | 7th November 2017

Does the thought of walking on damp carpet, seeing a watermark on the ceiling, or finding mould in the bathroom fill you with dread? Do you want to avoid paying thousands of dollars in home repairs caused by water damage?

A poorly waterproofed bathroom can decrease the value of your property and standard of living in many ways. Not only can water damage cost you thousands of dollars in repairs, but also put the health of your family at risk.

If you’re asking yourself, “Why should I waterproof my shower?” Let’s take a look at some of the most common reasons why.

Moisture Attracts Termites

Termites rely on copious amounts of timber and water to survive.

By introducing moisture into the substructure of the home, you create a perfect habit for termites to live and breed. These sections of the home are poorly ventilated and not designed to house water. This means the timber structures will rot and decay – making it an appetising source of energy for termites.

Concealed places are also preferred by termites. Therefore, finding them becomes harder and more expensive to treat the infestation.

Health and Safety

Did you know it only takes 24-48 hours for mould to start growing in damp conditions?

If a section of your home is poorly ventilated and exposed to moisture, you’re encouraging the growth of mould, mildew and bacteria. By letting this growth occur, you could be exposing your family to health hazards.

While not everyone is prone to the effects of mould, many people can suffer from:

  • Respiratory problems such as coughing, wheezing and trouble with breathing
  • Irritated throat
  • Sneezing and coughing fits
  • Nasal or sinus congestion

If you’re still wondering, “Why should I waterproof my shower?” Doing so could save you from a medical emergency.

Property Damage

Moisture can cause serious damage to your home.

From cracked floorboards to peeling paint, plasterboard decay, rotting or warped timber structures – fixing this damage can cost you thousands of dollars.

If a timber structure or wood product is exposed to water in a poorly ventilated place, the wood will rot and become decayed. This increases the chance of a support structure failing and causing extensive damage to the home.

No Insurance Coverage

“If my home is damaged by water, my insurance will cover it… right?”

Not exactly.

While each home insurance coverage is unique, many insurance providers clearly state that, unless you’re taking the necessary precautions to waterproof your home, you may be liable for the damage.

If you want to avoid paying a costly repair bill, waterproofing your shower is one of the best ways to keep your property investment safe.

Have Any Questions?

Want more information on why you should waterproof your shower? Call 1300 519 133 for advice from a professional leaking shower expert.

Showers Repairs Gold Coast

By Shower Sealed | 4th September 2016

Should you find yourself in the situation of suspecting you have a leaking shower, then call the number one leaking showers repair & sealing company on the Gold Coast.

Shower Sealed have exclusive Ultra Bond Technology that can seal over 95% of leaking showers without the need to remove tiles, saving you, your clients, and or your family, time, money and hassle.

A Standard service time ranges from 2.5 hours to 4 hours, and usually the leaking shower can be used within 24 to 48 hours, depending on the leaking showers service.

As we are fully licensed and insured, we can also provide traditional waterproofing, tiling and or shower renovation services as needed.

Most services are backed with a 12 Year Written Guarantee

Shower Sealed perform a thorough inspection on your leaking showers throughout Gold Coast, Tweed Coast & Brisbane. The team that perform our inspections have years of experience within the industry seeing literally 1000’s upon 1000’s of leaking showers prior to coming to yours or your clients property.

Free Quotes on leaking showers Gold Coast, Tweed Coast  & Brisbane

Please call us on 1300519133 or fill in our online call back form today

Showers Repairs Brisbane

By Shower Sealed | 23rd August 2016

The Team at Shower Sealed are your trusted local shower repair pro’s in Brisbane

With over 23 Years of experience performing sealing & shower repairs throughout Brisbane, we have seen just about every kind of shower repair problem possible. Having said this, even we get surprised as to how long people wait to fix a problem. 

Our suggestion when thinking about performing shower repairs is to not wait too long. Even if you are not a shower repair expert, as a home owner you tend to notice little differences with the shower and or surrounding areas of the shower. However unfortunately if you are like most people you tend to kind of pretend you don’t see those things, or think I’ll deal with that latter.

The bigger problem here is that when it involves leaking water then unfortunately the problem tends to get worse much quicker, and cause more damage than other maintenance issues within a home.

While our job at Shower Sealed is to try to save you the costly expense of ripping up and or renovating a leaking shower.  All too often we walk into showers that unfortunately have just been left too long and have caused major damage to the shower and or the surrounds of the shower.

We have even seen entire walls and or floors completely eaten out by termites, which are attacked to the moisture of a leaking shower. There have been a number of occasions where the shower has leaked so badly through the floor, that the floor is literally about to fall through.

Do you need sealing or shower repairs Brisbane?

Here are some the more obvious signs that you will require a shower repair in Brisbane.

  • Swollen door timbers
  • Wet carpets or floor boards adjoining the shower
  • Dark stains within the grout lines of the bathroom
  • Dark stains on ceilings below the shower
  • Damp musty smells within the bathroom
  • Discolored paint on walls adjoining the shower

A leakage from a shower is usually a result of the waterproofing below the tiles within the shower failing in some way shape or form, however with our advanced Ultra Bond Technology shower sealing process we can normally prevent the water even getting to the damaged membrane. However whether we can perform this service will depend on how much damage the leaking shower has caused, both inside the shower and or to the surrounds of the shower.

Next time you are in the shower have quick look around and if you see any of the following issues then call us for an obligation free quote on a shower repair in Brisbane.

  • Moldy lifting sealant where the floor and wall meet
  • Moldy lifting sealants where the wall and wall meet
  • Deteriorated grout within the floor, walls and or hob
  • Cracked grout within the floor, walls and or hob
  • Lifting or cracked tiles within the shower
  • Gaps around the waste drain section
  • Moldy silicone within the shower screen
  • Discolored grout within the shower

 

Shower Sealed perform a thorough inspection on your leaking shower throughout Brisbane Gold Coast and Tweed Coast. The team that perform our inspections have years of experience within the industry seeing literally 1000’s upon 1000’s of leaking showers prior to coming to yours or your clients property.

Free Quotes on Sealing and or shower repairs Brisbane, Gold Coast & Tweed Coast

Please call us on 1300519133 or fill in our online call back form today

Showers Repairs Brisbane, Gold Coast & Tweed Coast

By Shower Sealed | 4th July 2016

Always insist on an onsite inspection & quote?

Did you know that many companies within the shower repair & sealing industry, don’t even come out and look at your leaking shower? They ask you a couple of basic questions over the phone or internet, then give you some kind of one size fits all quote.

Yet they haven’t even seen the condition of the shower! Does this really make sense?

How can they offer an extensive warranty, or give the correct advice if they haven’t even seen the condition of your leaking shower?

Only an on-site inspection can ascertain the condition of a shower recess and provide you with the correct information and options available to fix your leaking shower.

We hear stories weekly from client’s that have contacted these style of companies thinking they have a set priced quote to fix their leaking shower, only to be told when the company gets to their home, that there will be extra works needed, and it will cost much more than was originally quoted.

Please always insist on an onsite inspection, then you or your family can make an informed decision.

Shower Sealed physically inspect every leaking shower, providing you with a detailed inspection results, quote and or advice. Call 1300 519 133 or fill in our online call back form.

Leaking Shower Sealing & Repairs Gold Coast, Brisbane, Tweed & Northern NSW's

By Shower Sealed | 22 June 2016

Why is Shower Sealed the most recommended shower Sealing & Repair Company in Queensland?

It’s because we genuinely care about our client’s needs. Understanding the frustrations and potential expense that owners, tenants, and/or property managers may go through when dealing with a leaking shower.  A leaking shower left too long can cause major damage to your valued investment.

Shower Sealed is a locally owned and operated family company with over 23 years’ experience in sealing & repairing leaking showers across Brisbane, Gold Coast, Tweed Heads and Northern NSW’s.

Our specialized team of industry trained professionals are 100% focused on providing our clients with a second to none service experience from start to finish.   

Shower Sealed offers a free of charge in-home inspection, that quickly determines the source of your leaking shower. We provide you or your clients with a detailed quote in “layman’s terms”, that will clearly outline the problem, and the specific works needed to stop your leaking shower.

Our experienced team physically access every leaking shower with the goal of saving you and or clients the costly expense of ripping up tiles, and/or fully renovating the leaking shower where ever possible.

Shower Sealed have exclusive Ultra Bond Technology that seals over 95% of leaking showers without the need to remove tiles. This is backed by a 12 year written Guarantee.

Should it be assessed that there are too many loose tiles, damage, and/or structural issues, then we also provide full rip out, waterproofing & tiling services as needed.

Our team at Shower Sealed are 100% committed to providing you with the highest quality service in the industry. Don’t take our word for it, please read what our clients have to say about our leaking shower sealing & repair service….

If you are on the Gold Coast, Brisbane or Northern Rivers and you have a leaking shower, then we would invite you to contact our team at Shower Sealed on 1300 519 133, or fill in our call back form, to book in a free of charge inspection and or quote.

We look forward to being of service to you, your family and or clients.

Testimonials - To read more testimonials click here

We have had multiple leaking showers over the time we've managed our Brisbane properties. Shower Sealed have done an exceptional job repairing those leaking showers. The quote was competitive and the work was of an exceptionally high quality. I will recommend your shower repairs to anyone else with leaking shower issues.

Mr. Grant - Brisbane

Just thought I would send you a quick note to thank you and your guys for the work carried out for us over the past few months. With over 160 properties under management we (and our landlords) appreciate a company that can deliver on service and price, to which your company do both. We look forward to continue working with you

Mr. Merkur - Principal

This letter confirms that Shower Sealed, has carried out remedial work on showers for us at our place. All work has been performed to a very high standard. Their workmanship was faultless. Their staff were courteous at all Times. We found so far as the quotation was concerned, it was most competitive. On completion of work, areas were left clean and tidy.

Mr. Davey - Manager

If you are on the Gold Coast, Brisbane, Tweed Heads or Northern Rivers and you have a leaking shower, then we would invite you to contact our team at Shower Sealed on 1300 519 133, or fill in our call back form, to book in a free of charge inspection and or quote today.

We look forward to being of service to you, your family and or clients. 

 
SERVICES
  • Shower Sealing
  • Re grouting
  • Tiling
  • Tiling Repairs
  • Shower Repairs
  • Shower Reno’s

Request FREE Quote

 
CALL BACK FORM
Full Name *
Phone # *
Email
Postcode *
Brief Message *
Type this in

RECOMMENDED BY
  • Builders
  • Plumbers
  • Real Estates
  • Strata
  • Complexes
  • High Rise
  • Home Owners
TRUSTED SUPPLIER TO
(but not limited to)
DID YOU KNOW?
That termites are attracted to wet damp timbers caused by leaking showers.


TERMITE DAMAGE

A leaking shower left too long can cause major damage to your house.


MAJOR DAMAGE